Search Results

Gasoline compression ignition (GCI) has been shown to offer benefits in the NOx-soot tradeoff over conventional diesel combustion while still achieving high fuel efficiency. However, due to gasoline’s low reactivity, it is challenging for GCI to attain robust ignition and stable combustion under cold operating conditions. Building on previous work to evaluate glow plug-assisted GCI combustion at cold idle, this work evaluates the use of a spark plug to assist combustion. The closed-cycle 3-D CFD model was validated against GCI test results at a compression ratio of 17.3 during extended cold idle operation under laboratory-controlled conditions. A market representative, ethanol-free, gasoline (RON92, E0) was used in both the experiment and the numerical analysis. Spark-assisted simulations were performed by incorporating an ignition model with the spark energy required for stable combustion at cold start.

Expanding upon the authors’ previous work which utilized a GT-Power model of the Cooperative Fuels Research (CFR) engine under Research Octane Number (RON) conditions, this work defines the boundary conditions of the CFR engine under Motored Octane Number (MON) test conditions. The GT-Power model was validated against experimental CFR engine data for primary reference fuel (PRF) blends between 60 and 100 under standard MON conditions, defining the full range of interest of MON for gasoline-type fuels. The CFR engine model utilizes a predictive turbulent flame propagation sub-model, and a chemical kinetic solver for the end-gas chemistry. The validation was performed simultaneously for thermodynamic and chemical kinetic parameters to match in-cylinder pressure conditions, burn rate, and knock point prediction with experimental data, requiring only minor modifications to the flame propagation model from previous model iterations.

The efficiency and emission potential of pre-chamber combustion in a Miller cycle light duty gasoline engine operated under part load was evaluated. Several pre-chamber designs that examine the engine performance tradeoffs with nozzle diameter, pre-chamber volume, number of nozzles, and pre-chamber fuel enrichment were investigated for both excess air and cooled external EGR dilution strategies. The introduction of pre-chamber jet ignition was observed to significantly reduce the main-chamber combustion duration while reducing cyclic variability under dilute conditions, benefiting from the long-reach ignition jets and enhanced turbulence. However, the pre-chamber design that provided the fastest combustion led to reduced brake efficiency primarily due to increased wall heat loss. Maintaining the total nozzle area while increasing the number of nozzles was identified as a means to minimize the additional heat loss and maintain fast burn rates.

Gasoline compression ignition (GCI) offers improved efficiency by harnessing gasoline’s low reactivity to induce an extended ignition delay that promotes partial premixing of air and fuel before combustion occurs. However, enabling GCI across the full engine operating load map poses several challenges. At high load, due to the elevated pressures and temperatures of the charge mixture, the ignition delay time shrinks, leading to diminished GCI efficiency benefits. At low load, insufficient temperatures and pressures can lead to combustion instability. Variable valve actuation offers a practical solution to these challenges by enabling effective compression ratio (ECR) control. In this paper, the effects of variable intake valve closings were investigated for high load operations in a prototype heavy-duty GCI engine, using a research octane number 93 gasoline fuel. The study focused on the 50% (B50) and the 75% (B75) load conditions at 1375 RPM.

Increasingly stringent exhaust and CO2 emissions regulations are driving advancements in combustion and after-treatment technologies in the passenger vehicle sector. One major challenge is to achieve low emissions over the full operating map as required by Real Driving Emissions (RDE) legislation. Gasoline Compression Ignition (GCI), an advanced combustion concept, has shown potential to increase fuel efficiency and reduce emissions. GCI harnesses gasoline’s low reactivity for longer ignition delay, thus promoting partially premixed air-fuel mixture for efficient combustion. To maintain low engine-out NOx over the load range, high Exhaust Gas Recirculation (EGR) is required that consequently elevates boost pressure requirements. To meet the high boost and EGR demands, while minimizing pumping losses require air-system optimization.

In this last decade, non-destructive X-ray measurement techniques have provided unique insights into the internal surface and flow characteristics of automotive injectors. This has in turn contributed to enhancing the accuracy of Computational Fluid Dynamics (CFD) models of these critical injection system components. By employing realistic injector geometries in CFD simulations, designers and modelers have identified ways to modify the injectors’ design to improve their performance. In recent work, the authors investigated the occurrence of cavitation in a heavy-duty multi-hole diesel injector operating with a high-volatility gasoline-like fuel for gasoline compression ignition applications. They proposed a comprehensive numerical study in which the original diesel injector design would be modified with the goal of suppressing the in-nozzle cavitation that occurs when gasoline fuels are used.

The combustion system of a heavy-duty diesel engine operated in a gasoline compression ignition mode was optimized using a CFD-based response surface methodology and a machine learning genetic algorithm. One common dataset obtained from a CFD design of experiment campaign was used to construct response surfaces and train machine learning models. 128 designs were included in the campaign and were evaluated across three engine load conditions using the CONVERGE CFD solver. The design variables included piston bowl geometry, injector specifications, and swirl ratio, and the objective variables were fuel consumption, criteria emissions, and mechanical design constraints. In this study, the two approaches were extensively investigated and applied to a common dataset. The response surface-based approach utilized a combination of three modeling techniques to construct response surfaces to enhance the performance of predictions.

In this work, the effects of ozone, hydrogen, carbon monoxide, and exhaust gas recirculation (EGR) addition to Haltermann gasoline combustion were investigated. For these additives, laminar and turbulent flame speeds were experimentally determined using spherically propagating premixed flames in a constant volume combustion vessel. Two initial mixture pressures of Po = 1 and 5 bar, two initial mixture temperatures of 358 and 373 K and a range of equivalence ratios (Ф) from 0.5 to 1 were investigated. The additives were added as single, binary and ternary mixtures to Haltermann gasoline over a wide range of concentrations. For the stoichiometric mixture, the addition of 10% H2, 5% CO and 1000 ppm O3 shows remarkable enhancement (80%) in SL0compared to neat Haltermann gasoline. In addition, for this same blend, increasing the mixture initial temperature and pressure results in a significant increase in SL0compared to the neat gasoline.

The current research octane number (RON) and motor octane number (MON) gasoline tests are inadequate for describing the auto-ignition reactivity of fuels in homogeneous charge compression ignition (HCCI) combustion. Intake temperature and engine speed are two important parameters when trying to understand the fuel auto-ignition reactivity in HCCI combustion. The objective of this study was to understand the effect of high intake temperature (between 100 and 200 °C) and engine speed (600 and 900 rpm) on the auto-ignition HCCI reactivity ratings of fuels using an instrumented Cooperative Fuel Research (CFR) engine. The fuels used for this study included blends of iso-octane/n-heptane, toluene/n-heptane, ethanol/n-heptane, and gasolines with varying chemical compositions and octane levels. The CFR engine was operated at 600 and 900 rpm with an intake pressure of 1.0 bar and an excess air ratio (lambda) of 3.

In order to further understand the sequence of events leading to stochastic preignition in a spark-ignition engine, a methodology previously developed by the authors was used to evaluate the propensity of a wide range of fuels to establishing propagating flames under conditions representative of those at which stochastic preignition (SPI) occurs. The fuel matrix included single component hydrocarbons, binary mixtures, and real fuel blends. The propensity of each fuel to establish a flame was correlated to multiple fuel properties and shown to exhibit consistent blending behaviors. No single parameter strongly predicted a fuel’s propensity to establish a flame, while multiple reactivity-based parameters exhibited moderate correlation. A two-stage model of the flame establishment process was developed to interpret and explain these results.

A two-stage PPCI-diffusion combustion process recently showed good potential to enable clean and fuel-efficient gasoline compression ignition (GCI) combustion at medium-to-high loads. By conducting closed-cycle 3-D CFD combustion analysis, a further step was undertaken in this work to evaluate and optimize the PPCI-diffusion combustion strategy at a full load operating point (2000rpm-23.5 bar IMEPcc) while keeping engine-out NOx below 1 g/kWh. The light-duty GCI engine used in this investigation featured a custom-designed piston bowl geometry at a 17.0 compression ratio (CR), a high pressure diesel fuel injection system, and advanced single-stage turbocharging. A split fuel injection strategy was used to enable the two-stage PPCI-diffusion combustion process. First, the injector spray pattern and swirl ratio effects were evaluated. In-cylinder air utilization and the PPCI-diffusion combustion process were notably influenced by the closed-cycle combustion system design.

In this work, a high temperature (HT) homogeneous charge compression ignition (HCCI) critical compression ratio (cCR) was defined as the compression ratio which resulted in HCCI combustion with a crank angle location of 50% fuel burned (CA50) of 3.0 degrees after top dead center (aTDC) while operating at an equivalence ratio of 0.33 (λ = 3), an intake pressure of 1.0 bar (naturally aspirated), an intake temperature of 473 K (200°C), and an engine speed of 600 rpm. Using a Cooperative Fuel Research engine, the HT HCCI cCR of seven alcohol fuels were experimentally determined and found to be ordered as follows (ordered from least reactive to most reactive): isopropanol > sec-butanol > methanol ≈ ethanol ≈ n-propanol ≈ isobutanol > n-butanol. The HT HCCI cCR for the alcohol fuels correlated well with experimental HCCI data from a modern gasoline direct injection (GDI) engine architecture with a pent-roof head and a rebreathe valvetrain.

This work focuses on reducing the computational effort of a 0-dimensional combustion model developed for compression ignition engines operating on gasoline-like fuels. As in-cylinder stratification significantly contributes to the ignition delay, which in turn substantially influences the entire gasoline compression ignition combustion process, previous modeling efforts relied on the results of a 1-dimensional spray model to estimate the in-cylinder fuel stratification. Insights obtained from the detailed spray model are leveraged within this approach and applied to a reduced order model describing the spray propagation. Using this computationally efficient combustion model showed a reduction in simulation time by three orders of magnitude for an entire engine cycle over the combustion model with the 1-dimensional spray model.

An increase in spark-ignition engine efficiency can be gained by increasing the engine compression ratio, which requires fuels with higher knock resistance. Oxygenated fuel components, such as methanol, ethanol, isopropanol, or iso-butanol, all have a Research Octane Number (RON) higher than 100. The octane numbers (ON) of fuels are rated on the CFR F1/F2 engine by comparing the knock intensity of a sample fuel relative to that of bracketing primary reference fuels (PRF). The PRFs are a binary blend of iso-octane, which is defined to an ON of 100, and n-heptane, which represents an ON of 0. Above 100 ON, the PRF scale continues by adding diluted tetraethyl lead (TEL) to iso-octane. However, TEL is banned from use in commercial gasoline because of its toxicity. The ASTM octane number test methods have a “Fit for Use” test that validate the CFR engine’s compliance with the octane testing method by verifying the defined ON of toluene standardization fuels (TSF).

Multi-mode combustion strategies may provide a promising pathway to improve thermal efficiency in light-duty spark ignition (SI) engines by enabling switchable combustion modes, wherein an engine may operate under advanced compression ignition (ACI) at low load and spark-assisted ignition at high load. The extension from the SI mode to the ACI mode requires accurate control of intake charge conditions, e.g., pressure, temperature and equivalence ratio, in order to achieve stable combustion phasing and rapid mode-switches. This study presents results from computational fluid dynamics (CFD) analysis to gain insights into mixture charge formation and combustion dynamics pertaining to auto-ignition processes. The computational study begins with a discussion of thermal wall boundary condition that significantly impacts the combustion phasing.

In recent years gasoline compression ignition (GCI) has been shown to offer an attractive combination of low criteria pollutants and high efficiency. However, enabling GCI across the full engine load map poses several challenges. At high load, the promotion of partial premixing of air and fuel is challenging due to the diminished ignition-delay characteristics at high temperatures, while under low load operations, maintaining combustion robustness is problematic due to the low reactivity of gasoline. Variable valve actuation (VVA) offers a means of addressing these challenges by providing flexibility in effective compression ratio. In this paper, the effects of VVA were studied at high loads in a prototype heavy-duty GCI engine using a gasoline research octane number (RON) 93 at a geometric compression ratio (CR) of 15.7. Both late intake valve closing (LIVC) and early intake valve closing (EIVC) strategies were analyzed as a measure to reduce the effective compression ratio.

The study of spray-wall interaction is of great importance to understand the dynamics that occur during fuel impingement onto the chamber wall or piston surfaces in internal combustion engines. It is found that the maximum spreading length of an impinged droplet can provide a quantitative estimation of heat transfer and energy transformation for spray-wall interaction. Furthermore, it influences the air-fuel mixing and hydrocarbon and particle emissions at combusting conditions. In this paper, an analytical model of a single diesel droplet impinging on the wall with different inclined angles (α) is developed in terms of βm (dimensionless maximum spreading length, the ratio of maximum spreading length to initial droplet diameter) to understand the detailed impinging dynamic process.

National concerns over energy consumption and emissions from the transportation sector have prompted regulatory agencies to implement aggressive fuel economy targets for light-duty vehicles through the U.S. National Highway Traffic Safety Administration/Environmental Protection Agency (EPA) Corporate Average Fuel Economy (CAFE) program. Automotive manufacturers have responded by bringing competitive technologies to market that maximize efficiency while meeting or exceeding consumer performance and comfort expectations. In a collaborative effort among Toyota Motor Corporation, Argonne National Laboratory (ANL), and the National Renewable Energy Laboratory (NREL), the real-world savings of one such technology is evaluated. A commercially available Toyota Highlander equipped with two-phase cold storage technology was tested at ANL’s chassis dynamometer testing facility.

In this study, the combustion system of a light-duty compression ignition engine running on a market gasoline fuel with Research Octane Number (RON) of 91 was optimized using computational fluid dynamics (CFD) and Machine Learning (ML). This work was focused on optimizing the piston bowl geometry at two compression ratios (CR) (17 and 18:1) and this exercise was carried out at full-load conditions (20 bar indicated mean effective pressure, IMEP). First, a limited manual piston design optimization was performed for CR 17:1, where a couple of pistons were designed and tested. Thereafter, a CFD design of experiments (DoE) optimization was performed where CAESES, a commercial software tool, was used to automatically perturb key bowl design parameters and CONVERGE software was utilized to perform the CFD simulations. At each compression ratio, 128 piston bowl designs were evaluated.

A 500-hour test cycle has been used to evaluate the durability of a prototype high pressure common rail injection system operating up to 1800 bar with E10 gasoline. Some aspects of the original diesel based hardware design were optimized in order to accommodate an opposed-piston, two-stroke engine application and also to mitigate the impacts of exposure to gasoline. Overall system performance was maintained throughout testing as fueling rate and rail pressure targets were continuously achieved and no physical damage was observed in the low-pressure components. Injectors showed no deviation in their flow characteristics after exposure to gasoline and high resolution imaging of the nozzle spray holes and pilot valve assemblies did not indicate the presence of cavitation damage. The high pressure pump did not exhibit any performance degradation during gasoline testing and teardown analysis after 500 hours showed no evidence of cavitation erosion.